Charging a car at home comes down to four unglamorous things: panel capacity, a clear route for the wire, where the car actually parks, and who signs off on the work. All four are easier to settle before the drywall goes up.
If you drive an electric car now, or think you might during the years you own the home, the garage is where that decision gets made. Not at the dealership. The useful part is that almost everything that matters can be sorted out while the house is still a set of drawings, and it gets progressively harder and more expensive to sort out after the drywall is up and the driveway is poured.
This article is about what to look at on a garage plan and what to ask. It is not about any particular home at The Valleys of Thornhill, and this site is independent of the builders, so treat everything here as questions to put to them rather than answers about their homes.
Four things decide whether a garage can charge a car
Home charging is not complicated electrically. A Level 2 charger is a 240-volt appliance, in the same family as a range or a clothes dryer. What makes it awkward in a new build is that nobody planned for it unless somebody asked.
1. Spare capacity in the electrical panel
A charger draws a substantial, sustained load for hours at a time. Whether your panel can carry it depends on the size of the service coming into the house and on everything else already connected to it: heat pump or air conditioner, range, dryer, hot water, and anything else electric rather than gas.
Ask the builder two specific questions: what amperage is the electrical service on this home, and how many spare breaker positions will the panel have when the house is finished. The second number is the one people forget. A panel can have capacity on paper and no physical room left for another double-pole breaker.
If the answer is tight, that does not end the conversation. Load-management devices exist that let a charger share a circuit or throttle itself when the rest of the house is drawing hard. That is a licensed electrician's call, not yours, but it is worth knowing the option is there before you assume the house cannot do it.
2. A route from the panel to the garage wall
Find the electrical panel on the plan. In many homes it sits in the basement or a mechanical room. Then trace, roughly, how a cable would get from there to the garage wall where you want the charger.
If the panel is near the garage, this is short and cheap. If it is at the far end of a finished basement, the run is longer, and after closing it means either fishing wire through finished walls or running surface conduit where you can see it. A length of empty conduit installed during construction costs very little and solves the problem permanently, which is why the rough-in is usually the better value than the charger itself.
3. Where the car actually parks
Chargers come with a fixed cable length, commonly in the range of five to eight metres depending on the unit. Look at the garage on the plan and work out which wall and which end of that wall is closest to where the car's charge port will sit. Then check what else is on that wall: the door opener, the water line to a hose bib, stairs down into the house, a man door to the side yard.
In a two-car garage, the question is which of the two bays gets the charger, and whether the cable can reach the other bay if you later have two electric cars. In a three-car configuration, the far bay may be a long reach from a panel-side wall. This is the detail most people discover after they park a car in the space for the first time.
Our overview of garages and parking across the homes here covers the configurations in more general terms.
4. Outlet or hardwired
Two common approaches. One is a 240-volt receptacle in the garage, into which a plug-in charger goes. The other is a circuit terminated at a box, with the charger wired directly to it. Plug-in units are easier to replace and to take with you. Hardwired units are sometimes required for higher-amperage installations and look tidier.
Either way, the work is done by a licensed electrical contractor and is subject to inspection under the Ontario Electrical Safety Code. If you have a contractor do it after closing, confirm they are filing a notification with the Electrical Safety Authority and that you receive the certificate of inspection. Keep it; your insurer may ask.
"EV rough-in" can mean several different things
This is where buyers get caught. The phrase appears on feature lists and in sales conversations without a fixed meaning. It might mean any of the following:
- An empty conduit from the panel area to a point on the garage wall, with no wire in it
- Conduit with wire pulled through, terminated in a blank box, no breaker installed
- A complete 240-volt circuit with breaker and receptacle, ready for a plug-in charger
- A reserved breaker space and nothing else
Those are four very different pieces of work. Ask which one is being described, in writing, and ask for the conductor size or circuit amperage if a circuit is included. A 30-amp circuit and a 60-amp circuit both qualify as "EV ready" in casual conversation and they charge at noticeably different rates.
The place to pin this down is the paperwork. Reading a builder's features and finishes list carefully is the habit that catches this sort of ambiguity, and anything you agree to verbally should end up on the schedule attached to your agreement.
Comparing across different homes
The three builders at this community deliver different products: Treasure Hill builds two-car garage townhomes, Starlane Home Corp. builds 33-foot singles with two-car garages, and Greenpark Group builds 38-foot and 50-foot singles with two- and three-car garages. Those differences change the geometry of the problem, not the principles. A larger garage gives you more wall to work with and more distance to cover; a townhome garage may put the panel closer but leave less room to manoeuvre around a parked car with a cable.
For a broader look at how the builders differ, see the three builders compared or the individual builder pages. For specifications on any particular home, go to the builder directly. They are the only source that can tell you what is included.
Where in the process to raise it
Electrical selections are typically handled at the design appointment, and that appointment usually happens well before the house is framed. Go in knowing what you want to ask for, because the session moves quickly and covers a great deal of ground. Our guide to what actually happens at the design appointment explains the sequence.
If you are earlier than that, raise it when you are reviewing the agreement. There may be a deadline after which electrical changes are no longer accepted, and that deadline is driven by the construction schedule, not by the builder's preference.
Verifying it at the pre-delivery inspection
Whatever was promised, confirm it exists before you take keys. At the pre-delivery inspection, find the garage termination point, open the panel cover if the representative allows it, and confirm the breaker is there and labelled. If the deliverable was empty conduit, confirm both ends are accessible and that the conduit is not buried behind finished wall board with no pull point.
Note anything missing on the PDI form. That form is the record, and items on it are handled through the warranty process rather than as a favour.
If you are not buying an electric car yet
The honest trade-off: paying for a full charging circuit you may never use is money spent on a maybe. Paying for empty conduit is a small cost that removes the hardest part of the job later, because the expensive part of a retrofit is almost never the wire, it is getting the wire through finished space.
If the choice is binary and you are undecided, the conduit is usually the one worth taking. If the builder does not offer it, note where the panel sits and how a future run would get to the garage, and keep that in mind when you are choosing a lot and a layout.
Separately, it is worth confirming how your electricity account is set up and whether time-of-use pricing applies, since charging overnight behaves differently on your bill than charging at dinner time. Our guide to setting up utilities in a new Vaughan home covers the account side, and your local distribution company's website is the authority on rate structures.
If you have questions about how any of this applies to homes in this community, get in touch, and confirm the specifications themselves with the builder.
Have Questions About Pre-Construction?
Matthew Caporiccio can help you understand pricing, deposit structures, and availability at The Valleys of Thornhill and other pre-construction projects across the GTA.
